64EK26
Members-
Posts
566 -
Joined
-
Last visited
-
Days Won
7
64EK26 last won the day on April 8
64EK26 had the most liked content!
Reputation
22 ExcellentPersonal Information
-
Location
Fareham Hants
-
Interests
Series Land rovers, valve radios (espically Larkspur)
-
Occupation
Recently Retired (yipee)
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
-
Hi Forgot to add, they need to be knocked out with a drift as the splines in the pin nearest the nut are designed to bed into the shackle to stop the shackle bolt from rotating Cheers Richard
-
64EK26 started following Ebay Land Rover FFR , Bedford mw shackle pin removal , Overlord Show 2024 and 2 others
-
Hi This is what the shackle pin look like, minus grease nipple (this one was badly worn and was replaced - I got my new ones from Norman Aish) This was when it was fitted Hope this helps Cheers Richard
-
Hi Don't forget it is the Overlord Show next week end see https://www.overlordshow.co.uk/ See you there Cheers Richard
-
Hi Sorry these have now gone Cheers Richard
-
MWR - An introduction / Restoration blog.
64EK26 replied to Rob.Brindley's topic in British Vehicles
Hi Clive That make sense, it would be logical to be struck off census before being sold. The original cost of 13RE80 was £273 and 13 Shillings Cheers Richard -
MWR - An introduction / Restoration blog.
64EK26 replied to Rob.Brindley's topic in British Vehicles
Hi 13RE80 was sold at Ruddington Auctions on 12th June 1961 43YR07 was sold at Ruddington Auctions on 10th November 1960 Hope this helps Cheers Richard -
Hi I have a BSA 300w 24v Charger for sale (post war) , £150 collection from Fareham (nr. Portsmouth) I did have it running several years ago, but is sold as seen Message me if interested Cheers Richard
-
restoration Bedford MW restoration project 2012/2013
64EK26 replied to Danny P's topic in Blogs of MV restorations
Hi Danny This is what the bearing looks like Length 1.18" (30mm) ID 0.905" (23mm) OD 1.383" (35mm) Cheers Richard -
restoration Bedford MW restoration project 2012/2013
64EK26 replied to Danny P's topic in Blogs of MV restorations
Hi Danny With the clamp bolt slacked off you should be able to rotate the steering cover sleeve without the main shaft turning. With the woodruff key removed you should be able to pull the steering cover sleeve off. I suspect that the top end of your shaft has become rusted and thus is a very tight fit so you could use a soft ended hammer and tap the main shaft whilst holding the outer sleeve (also apply some penetrating oil on the shaft which will also help). I would recommend that you extract and clean and grease the bearing. The outer sleeve is designed to move up and down a bit so that the steering wheel can be snugly fitted. The alternative is that you pull off the rubber yoke (Item 94) which is clamped to the inside of the bulkhead, on mine it was split to aid easy removal (looking at your photo, I think yours is also split), the old gaiter can then be removed, as the diameter of the steering wheel end is greater than the main column use some washing on the new gaiter so the it can be eased over the steering wheel end. Hope this all make sense, next week end when I get access to my spare steering box I will send you some additional photos. Cheers Richard -
Hi Been searching through my in-service photos, the best I can come up with is this Jerry can holder ? Also just noticed, the dexion racking is quite different Cheers Richard
-
Hi - Not to hand, will post one later in the week, but this is the type I have (never seen one with legs on before) https://www.ebay.co.uk/itm/195905929538 Cheers Richard
-
Hi - don't know if it was fitted when in service (spent all its service life in Northern Ireland), when I restored it, there were 'witness marks' to show that a bracket had been fitted there at some point. The jerry can holder mounting holes align perfectly with the holes in the 'rear bulkhead' so that is why I fitted one. Cheers Richard
-
Hi I have one of these in my Rover8... Also can't find the part number in any of mine either, but the clamping bracket that holds the Jerry can in place does have a part number 333464 see https://www.seriesparts.co.uk/PartDetail?stockid=287 I use it for water as I have a slight leak in my radiator Cheers Richard
-
Thanks It will make a good doorstop Cheers Richard